Wire

General Wire PH-DR-B Drain-Rooter PH Basic Unit with 5/16" x 50' Cable and HCS Cutter Set

General Wire PH-DR-B Drain-Rooter PH Basic Unit with 5/16" x 50' Cable and HCS Cutter Set The General Wire PH-DR-B Drain-Rooter Includes: Drain-Rooter PH Basic Unit Including Power Cable Feed, 4' Guide Hose, Drum, Variable Speed Motor with Reversing Switch, Water-Proof Air Foot Switch, Plastic Cartridge, Leather Gloves, 5/16" x 50' Cable, and HECS Cutter Set. General Wire PH-DR-B Drain-Rooter Features: Equipped with a variable speed power cable feed and variable speed motor, the Drain-Rooter PH makes drain cleaning jobs cleaner and easier. The Drain-Rooter PH feeds and retrieves the cable at up to 16 feet per minute. A four-foot guide hose eliminates cable whipping, dirty fixtures and messy floors. And the drum speed can be varied by changing the pressure on the foot pedal, making it easier to thread the boring head through strainers or crossbars. The Drain-Rooter PH is a real labor-saver on long jobs or when working in a cramped area where the weight of the machine could get burdensome. It can be operated in both horizontal and vertical positions to get closer to the drain opening. General Wire PH-DR-B Drain-Rooter Specifications: . Weight: 22 lbs. (10 kg) (without cable) . Dimensions: 22" deep x 13-1/2" wide x 15" high (without hose) (56 cm x 34 cm x 38 cm) . Drum: Heavy gauge stamped aluminum with inner drum to prevent cable tangling. . Capacity: 50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. . All cables are left hand wound and reinforced with a wire rope center. . Power Cable Feed: Drives 1/4", 5/16" and 3/8" cables. . Cutter Set: Arrow Head, Boring Gimlet, Down Head Boring Gimlet, 1-1/4" Side Cutter Blade, Flexible Arrow Head Cutter . Motor: All ball-bearing, double insulated, reversible motor with speed control; 0-400 rpm, 230 and 240 volts available. . Foot Pedal: Pneumatic foot pedal controls variable speed motor. Leaves operator's hands free to control cable.

General Wire PH-DR-D Drain-Rooter PH Basic Unit with 1/4" x 50' Cable

General Wire PH-DR-D Drain-Rooter PH Basic Unit with 1/4" x 50' Cable The General Wire PH-DR-D Drain-Rooter Includes: Drain-Rooter PH Basic Unit INcluding Power Cable Feed, 4' Guide Hose, Drum, Variable Speed Motor with Reversing Switch, Water-Proof Air Foot Switch, Plastic Cartridge, Leather Gloves, and 1/4" x 50' Cable. General Wire PH-DR-D Drain-Rooter Features: Equipped with a variable speed power cable feed and variable speed motor, the Drain-Rooter PH makes drain cleaning jobs cleaner and easier. The Drain-Rooter PH feeds and retrieves the cable at up to 16 feet per minute. A four-foot guide hose eliminates cable whipping, dirty fixtures and messy floors. And the drum speed can be varied by changing the pressure on the foot pedal, making it easier to thread the boring head through strainers or crossbars.The Drain-Rooter PH is a real labor-saver on long jobs or when working in a cramped area where the weight of the machine could get burdensome. It can be operated in both horizontal and vertical positions to get closer to the drain opening. General Wire PH-DR-D Drain-Rooter Specifications: . Weight: 22 lbs. (10 kg) (without cable) . Dimensions: 22" deep x 13-1/2" wide x 15" high (without hose) (56 cm x 34 cm x 38 cm) . Drum: Heavy gauge stamped aluminum with inner drum to prevent cable tangling. . Capacity: 50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. All cables are left hand wound and reinforced with a wire rope center. . Power Cable Feed: Drives 1/4", 5/16" and 3/8" cables. . Cutter Set: Arrow Head, Boring Gimlet, Down Head Boring Gimlet, 1-1/4" Side Cutter Blade, Flexible Arrow Head Cutter . Motor: All ball-bearing, double insulated, reversible motor with speed control; 0-400 rpm, 230 and 240 volts available. . Foot Pedal: Pneumatic foot pedal controls variable speed motor. Leaves operator's hands free to control cable.

General Wire PO-JR/GT Sewerooter Junior Power Cable Feed and Guide Tube

General Wire PO-JR/GT Sewerooter Junior Power Cable Feed and Guide Tube

General Wire PO-S91/GT Speedrooter 91 Power Feed & Guide Tube

General Wire PO-S91/GT Speedrooter 91 Power Feed & Guide Tube

General Wire PO-703 Set of Rollers for Power Cable Feed

General Wire PO-703 Set of Rollers for Power Cable Feed

General Wire PO-RK Power Feed Repair Kit

General Wire PO-RK Power Feed Repair Kit

General Wire P-XP-B Mini-Rooter XP Basic Unit with 75' x 3/8" Cable

General Wire P-XP-B Mini-Rooter XP Basic Unit with 75' x 3/8" Cable The General Wire P-XP-B Mini-Rooter XP Includes: The Mini-Rooter XP Basic Unit Including MR-200-2 Drum, 8" Wheels, 1/3 HP Motor with Reverse Switch, 10' Power Cord, Ground Fault Interrupter, Water-Proof Air Foot Switch, Leather Gloves, and 75' x 3/8" Cable. General Wire P-XP-B Mini-Rooter XP Features: The Mini-Rooter XP gives you extra portability because 8" semi-pneumatic wheels let you keep the weight on the ground. An easy-grip handle folds down to save space and locks to use as an additional lifting handle. A roll bar protects the 1/3 hp motor when going up or down stairs. And the power cord and foot pedal can be stowed away on convenient cord wraps. The XP gives you extra performance and value, enabling you to clear clogged drain lines from 1-1/4" to 4" in diameter with just one machine. The drum easily holds 75 feet of 3/8" or 1/2" cable and features a free floating inner drum with an integral distributor tube to help prevent cable tangling. By switching to the optional J-Drum or dual drum you can handle smaller drain lines. You'll want to equip your XP with a power cable feed too. It makes a lot of tough jobs go much easier. Even with the power cable feed option, the drum is a snap to remove, taking less than a minute. Of course the XP comes with an air foot pedal and ground fault circuit interrupter for safety, and General's patented Flexicore wire rope center cable for durability. General Wire P-XP-B Mini-Rooter XP Specifications: . Weight: 37 lbs. (17 kg) without cable. . Dimensions: 18" deep x 12" wide x 19" high (45 cm x 30 cm x 46 cm). . Drum: Capacity of 75 ft. of 3/8" or 1/2" Flexicore wire rope center cable. Integral distributor tube. Oilite bronze and ball thrust bearings. . Cutter Set: Arrow Head, Boring Gimlet, 2" Side Cutter Blade, 1-1/2" U-Cutter. . Motor: 1/3 hp, with forward-off-reverse switch, spring- loaded mounting for proper belt tension. . Load Speed: 165 rpm. . Belt Guard: High impact plastic. . Power Cable Feed: Drives 1/2" and 3/8" cables. . Foot Pedal: Leaves operator's hands free to control cable. Uses air pressure, so there's no electrical contact between pedal and motor. . Power Cord: 10 ft. 3 wire vinyl covered with molded plug. In-line ground fault circuit interrupter. . Leather Gloves: With reinforced palm for hand protection and proper slippage when guiding cable.

General Wire P-XP-D Mini-Rooter XP Basic Unit with 75' x 1/2" Cable

General Wire P-XP-D Mini-Rooter XP Basic Unit with 75' x 1/2" Cable The General Wire P-XP-D Mini-Rooter XP Includes: The Mini-Rooter XP Basic Unit Including MR-200-2 Drum, 8" Wheels, 1/3 HP Motor with Reverse Switch, 10' Power Cord, Ground Fault Interrupter, Water-Proof Air Foot Switch, Leather Gloves, and 75' x 1/2" Cable. General Wire P-XP-D Mini-Rooter XP Features: The Mini-Rooter XP gives you extra portability because 8" semi-pneumatic wheels let you keep the weight on the ground. An easy-grip handle folds down to save space and locks to use as an additional lifting handle. A roll bar protects the 1/3 hp motor when going up or down stairs. And the power cord and foot pedal can be stowed away on convenient cord wraps. The XP gives you extra performance and value, enabling you to clear clogged drain lines from 1-1/4" to 4" in diameter with just one machine. The drum easily holds 75 feet of 3/8" or 1/2" cable and features a free floating inner drum with an integral distributor tube to help prevent cable tangling. By switching to the optional J-Drum or dual drum you can handle smaller drain lines. You'll want to equip your XP with a power cable feed too. It makes a lot of tough jobs go much easier. Even with the power cable feed option, the drum is a snap to remove, taking less than a minute. Of course the XP comes with an air foot pedal and ground fault circuit interrupter for safety, and General's patented Flexicore wire rope center cable for durability. General Wire P-XP-D Mini-Rooter XP Specifications: . Weight: 37 lbs. (17 kg) without cable. . Dimensions: 18" deep x 12" wide x 19" high (45 cm x 30 cm x 46 cm). . Drum: Capacity of 75 ft. of 3/8" or 1/2" Flexicore wire rope center cable. Integral distributor tube. Oilite bronze and ball thrust bearings. . Cutter Set: Arrow Head, Boring Gimlet, 2" Side Cutter Blade, 1-1/2" U-Cutter. . Motor: 1/3 hp, with forward-off-reverse switch, spring- loaded mounting for proper belt tension. . Load Speed: 165 rpm. . Belt Guard: High impact plastic. . Power Cable Feed: Drives 1/2" and 3/8" cables. . Foot Pedal: Leaves operator's hands free to control cable. Uses air pressure, so there's no electrical contact between pedal and motor. . Power Cord: 10 ft. 3 wire vinyl covered with molded plug. In-line ground fault circuit interrupter. . Leather Gloves: With reinforced palm for hand protection and proper slippage when guiding cable.

General Wire PV Power-Vee Basic Unit

General Wire PV Power-Vee Basic Unit Power-Vee Basic Unit PV Including Power Cable Feed, Variable Speed Motor with Reversing Switch, Plastic Cartridge. We've miniaturized our big machine power cable feed and put it on the Super-Vee to give you feeding speed and convenience you haven't seen before in a hand-held power drain cleaner. In tight or awkward places, the Power-Vee is like having a third hand. To feed the cable just start the Power-Vee and squeeze the feed lever; to retract it, reverse the motor and squeeze the lever. The feed handles 1/4", 5/16" and 3/8" cables. No adjustment, disassembly, or additional parts required. Our Dyna-Thrust bearing system helps carry the weight of the drum, significantly reducing wear on the motor shaft bearing and extending the life of the tool. Also adding to the Power-Vee's durability is the heavy-gauge stamped aluminum drum. Of course the cables are Flexicore with an integral wire rope center. Nobody makes cables like General. General Wire PV Power-Vee Basic Unit Specifications: . Motor: All ball-bearing, double-insulated, reversible motor with variable speed control; 0 - 500 rpm. . Drum: Heavy gauge stamped aluminum with inner drum to prevent cable tangling. . Capacity: 50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. . All cables are left hand wound and reinforced with a wire rope center. . Cable Cartridges: Light weight, impact resistant plastic. . Power Feed: Feeds 3/8" cable at 16 feet per minute. . CABLE NOT INCLUDED

General Wire PV-A-WC Power-Vee Basic Unit with Case, 1/4" x 25' and 3/8" x 25' Cables, HECS Cutter Set, and One Additional Cartridge

General Wire PV-A-WC Power-Vee Basic Unit with Case, 1/4" x 25' and 3/8" x 25' Cables, HECS Cutter Set, and One Additional Cartridge General Wire PV-A-WC Power-Vee Features: We've miniaturized our big machine power cable feed and put it on the Super-Vee to give you feeding speed and convenience you haven't seen before in a hand-held power drain cleaner. In tight or awkward places, the Power-Vee is like having a third hand. To feed the cable just start the Power-Vee and squeeze the feed lever; to retract it, reverse the motor and squeeze the lever. The feed handles 1/4", 5/16" and 3/8" cables. No adjustment, disassembly, or additional parts required. Our Dyna-Thrust bearing system helps carry the weight of the drum, significantly reducing wear on the motor shaft bearing and extending the life of the tool. Also adding to the Power-Vee's durability is the heavy-gauge stamped aluminum drum. Of course the cables are Flexicore with an integral wire rope center. Nobody makes cables like General. General Wire PV-A-WC Power-Vee Specifications: . Motor: All ball-bearing, double-insulated, reversible motor with variable speed control; 0 - 500 rpm. . Drum: Heavy gauge stamped aluminum with inner drum to prevent cable tangling. . Capacity: 50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. . All cables are left hand wound and reinforced with a wire rope center. . Cable Cartridges: Light weight, impact resistant plastic. . Power Feed: Feeds 3/8" cable at 16 feet per minute. . Cutter Set: Arrow Head, Boring Gimlet, Down Head Boring Gimlet, 1-1/4" Side Cutter Blade, Flexible Arrow Head Cutter

General Wire PV-C-WC Power-Vee Basic Unit with 1/4" x 50' and 3/8" x 35' Cables, and HECS Cutter Set

General Wire PV-C-WC Power-Vee Basic Unit with 1/4" x 50' and 3/8" x 35' Cables, and HECS Cutter Set General Wire PV-C-WC Power-Vee Features: We've miniaturized our big machine power cable feed and put it on the Super-Vee to give you feeding speed and convenience you haven't seen before in a hand-held power drain cleaner. In tight or awkward places, the Power-Vee is like having a third hand. To feed the cable just start the Power-Vee and squeeze the feed lever; to retract it, reverse the motor and squeeze the lever. The feed handles 1/4", 5/16" and 3/8" cables. No adjustment, disassembly, or additional parts required. Our Dyna-Thrust bearing system helps carry the weight of the drum, significantly reducing wear on the motor shaft bearing and extending the life of the tool. Also adding to the Power-Vee's durability is the heavy-gauge stamped aluminum drum. Of course the cables are Flexicore with an integral wire rope center. Nobody makes cables like General. General Wire PV-C-WC Power-Vee Specifications: . Motor: All ball-bearing, double-insulated, reversible motor with variable speed control; 0 - 500 rpm. . Drum: Heavy gauge stamped aluminum with inner drum to prevent cable tangling. . Capacity: 50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. . All cables are left hand wound and reinforced with a wire rope center. . Cable Cartridges: Light weight, impact resistant plastic. . Power Feed: Feeds 3/8" cable at 16 feet per minute. . Cutter Set: Arrow Head, Boring Gimlet, Down Head Boring Gimlet, 1-1/4" Side Cutter Blade, Flexible Arrow Head Cutter

Wheeler Rex 30050 1/2" IPS Chamfering Tool

Wheeler Rex 30050 1/2" IPS Chamfering Tool Wheeler Rex 30050 1/2" IPS Chamfering Tool Specifications: . Lightly bevels the end of polyethylene pipe prior to socket fusion. . Sized to allow marking for the proper end distance for the cold ring per ASTM F1056.

Wheeler Rex 30075 3/4" IPS Chamfering Tool

Wheeler Rex 30075 3/4" IPS Chamfering Tool Wheeler Rex 30075 3/4" IPS Chamfering Tool Specifications: . Lightly bevels the end of polyethylene pipe prior to socket fusion. . Sized to allow marking for the proper end distance for the cold ring per ASTM F1056.

Wheeler Rex 30100 1" IPS Chamfering Tool

Wheeler Rex 30100 1" IPS Chamfering Tool Wheeler Rex 30100 1" IPS Chamfering Tool Specifications: . Lightly bevels the end of polyethylene pipe prior to socket fusion. . Sized to allow marking for the proper end distance for the cold ring per ASTM F1056.

Wheeler Rex 30125 1-1/4" IPS Chamfering Tool

Wheeler Rex 30125 1-1/4" IPS Chamfering Tool Wheeler Rex 30125 1-1/4" IPS Chamfering Tool Specifications: . Lightly bevels the end of polyethylene pipe prior to socket fusion. . Sized to allow marking for the proper end distance for the cold ring per ASTM F1056.